 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| INTEGRATED CIRCUITS 74F353 Dual 4-input multiplexer (3-State) Product specification IC15 Data Handbook 1996 Jan 05 Philips Semiconductors Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 FEATURES * Inverting version of 74F253 * 3-State outputs for bus interface and multiplex expansion * Common select inputs * Separate Output Enable Inputs DESCRIPTION The 74F353 has two identical 4-input multiplexers with 3-State outputs which select two bits from four sources selected by common Select inputs (S0, S1). When the individual Output Enable (OEa, OEb) inputs of the 4-input multiplexers are High, the outputs are forced to a high impedance (Hi-Z) state. The 74F353 is the logic implementation of a 2-pole, 4-position switch; the position of the switch being determined by the logic levels supplied to the two common Select inputs. To avoid exceeding the maximum current ratings when the outputs of the 3-State devices are tied together, all but one device must be in the high-impedance state. Therefore, only one Output Enable must be active at a time. PIN CONFIGURATION OEa S1 I3a I2a I1a I0a Ya GND 1 2 3 4 5 6 7 8 16 15 14 13 12 11 10 9 VCC OEb S0 I3b I2b I1b I0b Yb SF00891 TYPE 74F353 TYPICAL PROPAGATION DELAY 6.0ns TYPICAL SUPPLY CURRENT (TOTAL) 11mA ORDERING INFORMATION DESCRIPTION 16-pin plastic DIP 16-pin plastic SO COMMERCIAL RANGE VCC = 5V 10%, Tamb = 0C to +70C N74F353N N74F353D PACKAGE DRAWING NUMBER SOT38-4 SOT162-1 INPUT AND OUTPUT LOADING AND FAN-OUT TABLE PINS I0a-I3a I0b-I3b S0, S1 OEa OEb Ya, Yb DESCRIPTION Port A data inputs Port B data inputs Common Select inputs Port A Output Enable input (active Low) Port B Output Enable input (active Low) 3-State outputs 74F (U.L.) HIGH/LOW 1.0/1.0 1.0/1.0 1.0/1.0 1.0/1.0 1.0/1.0 150/40 LOAD VALUE HIGH/LOW 20A/0.6mA 20A/0.6mA 20A/0.6mA 20A/0.6mA 20A/0.6mA 3mA/24mA NOTE: One (1.0) FAST unit load is defined as: 20A in the High state and 0.6mA in the Low state. LOGIC SYMBOL 6 5 4 3 10 11 12 13 IEC/IEEE SYMBOL 14 2 0 1 G 0 3 I0a 14 2 1 15 S0 S1 OEa OEb I1a I2a I3a I0b I1b I2b I3b 1 6 5 4 3 EN 0 1 2 3 MUX 7 Ya Yb 15 10 11 12 9 VCC = Pin 16 GND = Pin 8 7 9 13 SF00892 SF00893 1996 Jan 05 2 853-0103 16188 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 LOGIC DIAGRAM OEa 1 I0a 6 I1a 5 I2a 4 I3a 3 S1 2 S0 14 I0b 10 I1b 11 I2b 12 I3b 13 OEb 15 7 VCC = Pin 16 GND = Pin 8 Ya 9 Yb SF00894A FUNCTION TABLE INPUTS S0 X L L H H L L H H S1 X L L L L H H H H I0 X L H X X X X X X I1 X X X L H X X X X I2 X X X X X L H X X I3 X X X X X X X L H OE H L L L L L L L L OUTPUT Y Z H L H L H L H L NOTES: H = High voltage level L = Low voltage level X = Don't care Z = High impedance "off" state 1996 Jan 05 3 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 ABSOLUTE MAXIMUM RATINGS (Operation beyond the limit set forth in this table may impair the useful life of the device. Unless otherwise noted these limits are over the operating free-air temperature range.) SYMBOL VCC VIN IIN VOUT IOUT Tamb Tstg Supply voltage Input voltage Input current Voltage applied to output in High output state Current applied to output in Low output state Operating free-air temperature range Storage temperature PARAMETER RATING -0.5 to +7.0 -0.5 to +7.0 -30 to +5 -0.5 to VCC 48 0 to +70 -65 to +150 UNIT V V mA V mA C C RECOMMENDED OPERATING CONDITIONS SYMBOL VCC VIH VIL IIK IOH IOL Tamb Supply voltage High-level input voltage Low-level input voltage Input clamp current High-level output current Low-level output current Operating free-air temperature range 0 PARAMETER LIMITS MIN 4.5 2.0 0.8 -18 -3 24 70 NOM 5.0 MAX 5.5 UNIT V V V mA mA mA C DC ELECTRICAL CHARACTERISTICS (Over recommended operating free-air temperature range unless otherwise noted.) SYMBOL PARAMETER TEST CONDITIONS1 VCC = MIN, VIL = MAX, , , VIH = MIN, IOH = MAX VCC = MIN, VIL = MAX, , , VIH = MIN, IOL = MAX VCC = MIN, II = IIK VCC = MAX, VI = 7.0V VCC = MAX, VI = 2.7V VCC = MAX, VI = 0.5V VCC = MAX, VO = 2.7V VCC = MAX, VO= 0.5V VCC = MAX ICCH ICC Supply current (total) ICCL ICCZ VCC = MAX OEn=Sn=In=GND OEn=Sn=GND, In=4.5V OEn=4.5V, Sn=In=GND -60 9 11 13 LIMITS MIN TYP2 MAX UNIT V 3.3 0.35 0.35 -0.73 0.50 0.50 -1.2 100 20 -0.6 50 -50 -150 14 20 23 V V V V A A mA A A mA mA mA mA VO OH High-level High level output voltage 10%VCC 5%VCC 10%VCC 5%VCC 2.4 2.7 VO OL VIK II IIH IIL IOZH IOZL IOS Low-level Low level output voltage Input clamp voltage Input current at maximum input voltage High-level input current Low-level input current Off-state output current High-level voltage applied Off-state output current Low-level voltage applied Short-circuit output current3 NOTES: 1. For conditions shown as MIN or MAX, use the appropriate value specified under recommended operating conditions for the applicable type. 2. All typical values are at VCC = 5V, Tamb = 25C. 3. Not more than one output should be shorted at a time. For testing IOS, the use of high-speed test apparatus and/or sample-and-hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise, prolonged shorting of a High output may raise the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOS tests should be performed last. 4 1996 Jan 05 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 AC ELECTRICAL CHARACTERISTICS LIMITS SYMBOL PARAMETER TEST CONDITION VCC = 5V Tamb = +25C CL = 50pF, RL = 500 MIN tPLH tPHL tPLH tPHL tPZH tPZL tPHZ tPLZ Propagation delay In to Yn Propagation delay Sn to Yn Output Enable time to High or Low level Output Disable time from High or Low level Waveform 1 Waveform 2 Waveform 3 Waveform 4 Waveform 3 Waveform 4 3.0 1.5 5.0 3.0 4.0 4.0 2.5 1.5 TYP 5.0 3.0 9.0 6.0 6.0 6.5 4.0 2.5 MAX 7.0 5.0 12.0 8.5 8.0 8.0 5.5 6.0 VCC = 5V 10% Tamb = 0C to +70C CL = 50pF, RL = 500 MIN 3.0 1.0 4.5 3.0 3.5 3.5 2.0 1.5 MAX 8.0 5.5 12.5 9.5 9.0 9.0 6.0 7.0 ns ns ns ns UNIT AC WAVEFORMS For all waveforms, VM = 1.5V In Sn VM tPHL VM tPLH VM tPHL VM tPLH Yn VM VM Yn VM VM SF00895 SF00896 Waveform 1. Propagation Delay, Data to Output Waveform 2. Propagation Delay, Select to Output OEn VM tPZH VM tPHZ VOH -0.3V OEn VM tPZL VM VM tPLZ Yn VM 0V Yn VOL +0.3V SF00897 SF00898 Waveform 3. 3-State Output Enable Time to High Level and Output Disable Time from High Level Waveform 4. 3-State Output Enable Time to Low Level and Output Disable Time from Low Level 1996 Jan 05 5 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 TEST CIRCUIT AND WAVEFORMS VCC 7.0V VIN PULSE GENERATOR RT D.U.T. VOUT RL NEGATIVE PULSE 90% VM 10% tTHL (tf ) CL RL tTLH (tr ) 90% POSITIVE PULSE 10% tTHL (tf ) AMP (V) 90% VM tw 10% 0V tw VM 10% tTLH (tr ) 0V AMP (V) 90% Test Circuit for 3-State Outputs SWITCH POSITION TEST tPLZ tPZL All other SWITCH closed closed open VM Input Pulse Definition DEFINITIONS: RL = Load resistor; see AC electrical characteristics for value. CL = Load capacitance includes jig and probe capacitance; see AC electrical characteristics for value. RT = Termination resistance should be equal to ZOUT of pulse generators. INPUT PULSE REQUIREMENTS family amplitude VM 74F 3.0V 1.5V rep. rate 1MHz tw 500ns tTLH 2.5ns tTHL 2.5ns SF00777 1996 Jan 05 6 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 DIP16: plastic dual in-line package; 16 leads (300 mil) SOT38-4 1996 Jan 05 7 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 SO16: plastic small outline package; 16 leads; body width 7.5 mm SOT162-1 1996 Jan 05 8 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 NOTES 1996 Jan 05 9 Philips Semiconductors Product specification Dual 4-input multiplexer (3-State) 74F353 Data sheet status Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition [1] This data sheet contains the design target or goal specifications for product development. Specification may change in any manner without notice. This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips Semiconductors reserves the right to make chages at any time without notice in order to improve design and supply the best possible product. This data sheet contains final specifications. Philips Semiconductors reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Production [1] Please consult the most recently issued datasheet before initiating or completing a design. Definitions Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For detailed information see the relevant data sheet or data handbook. Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended periods may affect device reliability. Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or modification. Disclaimers Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application. Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless otherwise specified. Philips Semiconductors 811 East Arques Avenue P.O. Box 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 (c) Copyright Philips Electronics North America Corporation 1998 All rights reserved. Printed in U.S.A. Date of release: 03-98 Document order number: 9397 750 03684 Philips Semiconductors 1996 Jan 05 10 |
Price & Availability of N74F353D
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |